2/4/2024 0 Comments Torch Web Browser freeYou can follow any responses to this entry through the RSS 2.0 feed. This entry was posted on Augat 10:19 am and is filed under Uncategorized. Tags: blazer, butane, high capacity, lighter, pb-207, pb207, rugged, single, torch The PB-207 is the original, and most rugged. Blazer makes other, smoking-specific lighters based on the same design but I have heard mixed reviews of those. So, if you don’t mind not having the slickest lighter in the room, and you want something that’s rock solid reliable and doesn’t need to be refilled every day or two, the Blazer PB-207 is an excellent choice. I must just have bad luck, but it was an easy fix using cheap wire and a tiny drop of super glue. Your mileage may vary I wouldn’t put cheap butane in anything but a camping stove.Īll in all, for the $35 plus shipping and tax ($44 total), I have been nothing but happy with this lighter despite the igniter issue, which seems to be unique to me because I had never heard of such a thing happening. The torch is designed as a tool and while I wouldn’t put anything but triple refined (minimum) butane in ANY torch, according to multiple cigar forums and reviews I have found, it will run on the dirty cheap butane designed for stoves and soft flame lighters without issue due to the large ports and the very well designed valve system. Be prepared to release when this happens to avoid freezing your hands or wasting excess butane. It purges easily, and when full that taper does allow a certain amount of liquid butane to spray out from around the nozzle. –Punch a hole in an aluminum can on “low” in about 3 secondsĪn issue, not really a con, is that it fills FAST and there’s a bit of a taper to the fuel nozzle which is harder than most fill nozzles so it doesn’t get nicked when you try and depress it with another metal object (a no-no for most expensive lighters). –Solder up to 10 ga wire in a couple seconds by heating then removing the flame and applying solder Pro: It’s easy to clean and maintain with compressed air and a dry lint-free rag, it holds a TON of liquid butane, and it will: I find the flame is hot enough I can toast the foot of a cigar with non-contact heat…simply bringing the 2000 degree plus flame close to the cigar is enough to toast it, and bringing the flame in perpendicular to the end of the cigar without putting the hottest part of the flame on the cigar is more than enough to ignite the cigar without even the slightest amount of gas flavor or smell in your cigar. Modifying the lighter or removing the safety voids the warranty, and I could see instances where removing it may be useful, but really with some practice it becomes a technique, not a nuisance. It’s tricky at first but it becomes second nature after a while. It is nice to keep it from dispensing all the gas in your pocket, but you have to push up on a knurled lever to move it free of the body then while holding push down to ignite. It’s a fairly simple design which means there’s little to break and it’s fairly easy to fix when it needs it.Īnother “con” is the childproofing/safety scheme. I was able to easily service it with a small piece of 18 gauge wire and a small drop of super glue. Also, I had the igniter fall out of the lighter when I tried to adjust the spark gap because it had been dropped with the cap off and struck something. It will burn, on high, for 20 minutes continuously and will light approximately 100 cigars or probably four times that many cigarettes on one fill.Ī con is that the chain can snag when pocketed. A small lever on the opposite side will turn a 1.5-1.75″ flame to a 3″ flame, and according to the instructions the burn temperature is between 2000-2500 degrees Fahrenheit. Wind seems to affect ignition more than burning, so once lit it’s tough to put out. It is fairly windproof only a strong breeze will interfere with the torch operation. You can simply light it, lock it on with a small red button, then use it. It also has the said lock, which will allow the torch to be locked in the “ON” position when ignited so that it doesn’t have to be held down in order to use it. It has a cover which is attached by a fine chain, which keeps dirt and debris out of the torch area and has an angled piece that prevents the lock from allowing the torch to be capped with the gas locked on. It looks like a small scuba tank with a box attached to it. The Blaster PB-207 is ugly aesthetically. I had a Vertigo by Lotus shown here that, unfortunately, lost its valve in 4 months and wasn’t expensive enough to warrant replacing due to its low price. I have gone through several torch lighters over the years, ranging from the nichrome wire screen style to the venturi effect single torch to cheap duals and triples.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |